 |
|
MSO seals and gaskets ,inc manufacturer of hydraulic seals
pneumatic seals and oil seals and gaskets also extruder of
all type of shapes
LOW TOOLING COSTS!
IN-HOUSE MACHINE SHOP!
ULTRA-QUICK RESPONSE TIME!
LOW MINIMUMS!
SPECIALIZING IN PROTOTYPES
All seals are made from a superior
rubber compound that has been time tested and
approved by the U.S. Corps of Engineers.
Over these 40 years, we have accumulated well
over $100,000 in tooling that enables us to furnish these
seals fully molded, in
continuous lengths, and with
fully molded corners. Both
solid and hollow bulb constructions
are readily available, with either a
plain or TFE clad finish. Now, it's
time to introduce these MSO seals and gaskets ,inc
capabilities to the rest of the world.
ANY QUANTITY; NO QUANTITY TOO SMALL!
Typical J-Seal Cross Sections
Note: Dimensions are in inches; drawings
are not to scale!
Typical J-Seal Installations
Typical J-Seal Gate Fabrications
SILICONE
PRODUCTS
The most
outstanding characteristic of Silicone rubber is the
retention or its many desirable properties over the very
wide temperature range of -148º F to 600º F (-100º C to
315º C). It's impervious to water and oil, and has
chemical and fuel resistance at temperatures which
precludes the use of other chemical resistant elastomers,
with the possible exception of fluoroelastomers. It has
great electrical properties, and retains dielectric
strength, power factor and insulation resistance over
its' wide temperature range. It has good weathering
resistance; sunlight, ozone, oxygen, bacteria, fungus,
soil chemicals, etc. have very little deteriorating
effect.
| State-of-the-art synchronized extrusion &
continuous cure systems enable us to
producer extruded profiles to extremely
close tolerances and exacting
specifications. Continuous lengths or
spliced parts from silicone extrusions are
our forte |
|
Homogeneous, fabric reinforced and
bonded-to-metal silicone moldings are time-tested custom
made products also available from mso seals and gaskets
,inc Our entire Silicone Department is "housed" in a
separate air-conditioned building to prevent
contamination from outside sources. Quality products are
the result of this magnificient facility.
STANDARD RUBBER
PRODUCTS
BUFFER CHANNEL
EXTRUSIONS
Lathe Cut
Products
 |
Examples of Lathe Cut Products
| Seals
Drive Belts
Vibration Dampeners |
Bumpers
Bushings
Insulators |
Spacers
Connectors
Expansion Joints |
|
Lathe cut products are
manufactured from a cylindrical tube of rubber
by inserting a mandrel into the tube and cutting
the finished dimensions with a knife while the
mandrel is being turned at high speed in a
lathe-type machine. Lathe cut products have
numerous applications including: seals, drive
belts, feed wheels, vibration dampeners,
bumpers, bushings and insulators. |
Rubber
Covered Rolls
 |
Examples of Rubber Covered Wheels, Rolls
|
|
|
|
MSO seals and gaskets ,inc
rubber roll covering capabilities include the
use of virtually all elastomers which can be
applied to steel rolls up to 28" in diameter and
15 feet in length. Special surface finishes can
be furnished to meet the requirements of the
most demanding applications. |
PUMP DIAPHRAGMS
| - |
I.D. |
O.D. |
APPROX. HEIGHT |
| #23-7/8"11" |
1-3/4" |
| #35"13" |
1-3/8" |
| #45-1/2"15" |
2-1/4" |
SKIRTBOARD RUBBER
Our
Skirtboard rubber is made from 65 durometer SBR
rubber and is available in thicknesses of 1/4",
3/8", 1/2", 3/4" & 1" and in widths of 4", 5",
6", 8", 10" & 12" |
Viton® SHEET
Specifications
- Plate
Finish
- 1500 PSI
Tensile
- 300%
Elongation
- 70 ± 5
Duro, Shore A
- Color,
Black
|
|
Standard Sizes
- 1/16"
±.020" Tk. x 36" x 36"
- 1/8"
±.020" Tk. x 36" x 36"
- 1/4"
±.020" Tk. x 36" x 36"
- 3/8"
±.020" Tk. x 36" x 36"
- 1/2"
±.025" Tk. x 36" x 36"
|
|
We can extrude many shapes out of many materials such
as:
|
- NBR
- Neoprene
- EPDM
- Silicon
- Viton®
- ...
and many more
|
|
PROPERTIES OF
COMMON RUBBER ELASTOMERS
Natural Rubber (NR) (Gum)
As the name would indicate, this elastomer
occurs naturally and comes from the latex of
certain trees and plants. After the latex is
processed, it becomes an elastomer with excellent mechanical properties. It has excellent tensile, elongation, tear resistance and resilience. It has good abrasion
resistance and excellent low temperature
flexibility. Without special additives, it
has poor resistance to ozone, oxygen, sunlight
and heat. It has poor resistance to solvents and
petroleum products. Useful temperature range
is -67º F to +180º F (-55º C to +82º C).
Nitrile / Buna-N (NBR) (Hycar)
(Chemigum)
This is a copolymer of acrylonitrile and
butadiene. It has excellent physical
properties, however its claim to fame is
based on its resistance to water, petroleum
products and fuels. When compounded
properly, it has good low temperature
properties as well as good heat
resistance. It does not have good ozone,
oxygen or sunlight resistance without the
addition of special additives. Useful
temperature range is -40º F to +275º F (-40º C
to +135º C).
Neoprene / Chloroprene
(CR)
This elastomer is made by the polymerization
of Chloroprene. It has excellent physical
properties. It is moderately resistant to
petroleum products, sunlight, ozone and heat. It is flame resistant and will not
support combustion. Useful temperature range is
-40º F to +275º F (-40º C to +135º C).
Ethylene-Propylene (EPDM)
(EPR)
This is a terpolymer of ethylene, propylene
and a diene monomer. It has outstanding
resistance to oxygen, ozone, and sunlight. Its resistance to polar materials such as
phosphate esters, many ketones and alcohol. It has good electrical properties, low
temperature flexibility, excellent heat, water
and steam resistance. Its resistance to
petroleum products is poor. Useful
temperature range is -58º F to +300º F (-50º C
to +150º C).
Hypalon (CSM)
Hypalon is a chlor-sulfonated polyethylene.
It has outstanding oxygen, ozone and weather
resistance. It has excellent resistance
to corrosive chemicals as well as oil and
grease. It has excellent abrasion
resistance and excellent tensile and elongation.
Useful temperature range is -67º F to +320º F
(-50º C to +160º C).
Styrene Butadiene (SBR)
(Buna-S) (GRS)
This is a copolymer of styrene and butadiene. It has similar properties to natural rubber. Its resistance to solvents and petroleum
products is about the same as natural rubber.
Water resistance is better. Without special
additives, it is vulnerable to ozone, oxygen and
sunlight. Useful temperature range is -67º F
to +180º F (-55º C to +82º C).
Silicone
Silicone is made from sand and alkyl or aryl
halides. It is predominately inorganic
material. It has outstanding resistance to
temperature extremes. It has excellent
vibration damping, and reasonable
physical properties such as tensile and
elongation. Tear and abrasion resistance are
generally poor. Useful temperature range is
-148º F to +600º F (-100º C to +315º C).
Carboxylated Nitrile (CNBR)
This terpolymer has the excellent water,
oil and fuel resistance of conventional NBR.
It has superior abrasion resistance and load
bearing capabilities. It retains good
physical properties over a useful temperature
range of -40º F to +300º F (-40º C to +150º C).
Hydrogenated Nitrile (HNBR)
This polymer is produced by complete or
partial hydrogenation of NBR. The result is a
polymer with outstanding physical properties. It has good mechanical properties at elevated
temperature. It has excellent resistance
to many chemically aggressive technical oils.
Its useful temperature range is -40º F to +300º
F (-40º C to +150º C). |
|
| Send
us your drawings or samples. We will be glad to help you. |
|
|
 |
 |
Teflon